Check out these photos from Diego I.
Ever been to San Pedro, Belize? Just about every taxi is a Previa or Toyota Van.!
Would definatly want to go there now. Very nice to see!
Thanks Diego for the nice pictures.
 |
| Lots of Previa in San Pedro, Belize |
 |
| Sancas Plaza with Previas. |
Special thanks goes to ToyotaTarago1992 for doing this video:
https://www.youtube.com/watch?v=cxw6qV6yNps
Radiator flush, Motor Drain plug, Thermostat, [ TCR Tarago Previa Estima ]
"Under the right side seat there is a bleeding point on my van TCR11 but a buddy of mine has a TRC10 Gli and doesn't have one. I guess it depends on the make and year. What one of our member on the club page did was cut a coke bottle bottom off and put the on top of the radiator reservoir fill the system as much as he could and the coke bottle then go under the van and squeeze all the hoses to get the air out. this worked for him. Make sure to give the system a really good flush to avoid mixing coolants as mixed coolants can foam up in the engine and create an air pocket that's hard to get out. make sure thermostat is okay and radiator cap is good. Also helps to have the van on ramps so all air moves to the front. Make sure heaters are ON & when warm to temp give the van a few hard revs to really make the pump work and force water flow, you will fill the heat from the heaters if the water is flowing correctly."
Jimmy C."did a coolant flush the other day and was having a hard time bleeding the air out until i tryed taking the top rad hose off to fill with coolant but turned out letting the pressure out this way was enough and the coolant flowed properly through the system, couldnt find any bleed screws on the tcr10 but i guess loosening the rad drain plug would work too with hindsight. 2 weeks later shes still good."
------------------- ------------
"just did this. there are three small outlet tubes from the reservoir. one of mine was clogged with debris. pulled the reservoir and used wifeys knitting needle to unblock and now flows freely.
just wonder if this design somehow contributes to head gasket failure on high mileage previas somehow. there is a picture in chiltons manual for the engine drain location it is just in front of the oil pan and vertically oriented. be careful tightening, easy to strip. I drained 10 out of the 12 qts , filled with distilled water, repeated after running with heater on, then filled with Toyota red.50/50"
https://www.toyotanation.com/threads/previa-engine-block-coolant-drain-plug.1092545/
"There is a air bleed on top of the cylinder head. Its on the passenger side so you have to remove the access cover. Its a small banjo bolt air bleed. if you don't use it you have run the engine at high rpm for awhile to bleed the air. Perhaps you should try it. Bill"
----------------- ------------
https://www.toyotavantech.com/forum/showthread.php?3901-Previa-Engine-Coolant-Drain-Plug-location
"I just did this a couple weeks ago when I had to replace my 93 Previa's heater core, which meant I needed to drain the engine coolant from both the engine coolant drain plug and the radiator drain plug.
* Before starting I drained our Previa's engine coolant completely using both the Radiator draincock, as well as the engine block coolant drain plug. The engine block coolant drain plug is hard to see/find, but it's near where the engine oil drain plug is and is tucked up in that area. It was a 10mm bolt that was silver colored, if that helps. The picture in the Previa FSM does not help much in finding it.
I accessed the engine coolant drain plug from the passenger side of the vehicle about where the engine oil drain plug is located. My suggestion is to get under the vehicle and look in that area and look for a silver colored single 10mm bolt...it's obvious once you know where to look If you've never used it...it's almost impossible to find ;)"
"* After replacing the heater core I flushed the engine coolant system with distilled water, then filled it with Zerex Asian 50/50 pre-mixed engine coolant. It's the closest engine coolant to the Toyota "Red" that I could find locally (at NAPA)...it was either that or Prestone, and I wanted to go with as close to the Toyota "Red" coolant as possible."
"it is vertically oriented. do not overtighten, easy to strip"
